PLC – Allen-Bradley PLC-5, SLC500 y MicroLogix – Mantenimiento

This course is designed for maintenance personnel who have to maintaine and solve problems on the Allen-Bradley MicroLogix, SLC-500 and PLC-5 platforms. This course uses the Rockwell Software products RSLogix 5, RSLogix 500* and RSLinx.

Target Group
This course is designed for maintenance personnel who have to maintaine and solve problems on the Allen-Bradley MicroLogix, SLC-500 and PLC-5 platforms. This course uses the Rockwell Software products RSLogix 5, RSLogix 500* and RSLinx.

(Pre) Knowledge
To join this course a basic knowledge of Windows and Allen-Bradley PLC possibilities is required.

Global Contents
Maintenance personnel are often confronted with equipment from several manufacturers. This course recognises that maintenance personnel cannot build up a profound technical knowledge of all the equipment to be maintained. One needs to have sufficient knowledge of the equipment, coupled with knowledge of the installation to be able to diagnose the problem and then solve the problem.

With regard to PLC’s and programming software, the maintenance engineer needs to be able to access specific parts of the program and to examine the I/O status. Programming and documenting the program is of less importance. The maintenance engineers should be capable of making small changes to the program.

Problems are most likely to occur with the installation itself and this is reflected in the PLC by for instance a defective sensor, a badly working cylinder etc. These faults can be investigated via the programming software and the signal status can be presented dynamically. This is necessary, because designers are not always able to design their programs to register every possible fault and the potential cause.

The maintenance engineer should therefore be capable of executing the following actions:

  • To be able to identify if the PLC is still active and that there are no communication errors with the I/O or other coupled PLC’s.
  • To determine that the signal of the ‘suspected’ unit will show at the correct PLC input / output. To install and to start the programming software.
  • To make the internal I/O status of the signal visible:
    to call the ‘suspected’ section in the program;
    to make timer and counter files visible.
  • The maintenance engineer must be able to read the documentation, understand the structure of the PLC and be aware of the most commonly used PLC instructions.
  • To make links or to develop connections that changes the program conditions. Programming a counter and time measurement is desirable.
  • To make a backup of the changes made to the program. The maintenance engineer should also be capable of making an (original) backup of the program and be able to load it into the PLC.

Methods
ATS courses are given by highly qualified trainers, with practical knowledge, in professional ATS training centers or On-Site. Prior to the course an intake conversation can take place to define the participant(s) and the company’s requirements. Presentations (theory and examples) as well as practical exercises bring the courses to life. ATS courses are interactive, the trainer will always make sure the training contents link back to your situation.

Specific Contents

The following lessons will be followed

  • Lesson 1

    • Hardware of the Allen Bradley SLC500 / PLC5
    • I/O electric connections for various modules
    • Rack grouping
    • Developing, monitoring & documentation software
  • Lesson 2

    • General features of the Allen Bradley PLC family
    • IEC 1131 ‘compliant’ software structure
    • Ladder software and editing
  • Lesson 3

    • The RSlogix 5 / 500 programming package
    • Connecting the PLC and starting up the software
    • Selecting the PLC correct program
    • Help functions
    • Programming instructions, including the modifications of existing AND and OR gates, flip-flops, timer functions and counter functions
  • Lesson 4

    • To copy, to change and to store the PLC-programs
    • Fault finding
    • Off-line & On-line mode
    • Monitoring and modifying data variables
    • Forcing variables
    • Cross references
    • Software documentation
    • Using trends and data monitors
  • Lesson 5

    • Up- and downloading programs
    • Writing, testing, and documenting a PLC-program
    • Identifying data and data types and interpreting the different formats

PLC – Allen-Bradley PLC-5, SLC500 y MicroLogix – Mantenimiento

Fecha: Por solicitud
Ciudad: Spain
Precio:

Cursos en Control

Curso
PLC
Introduction to PLCs

This course is designed for maintenance/operator personnel who will be working with PLCs for the first time…


Leer más

Curso
PLC
Siemens S7 Mantenimiento y Análisis de Averías

Este curso ha sido diseñado para el personal de mantenimiento que necesite identificar y solucionar problemas con el procesador…

Leer más

Curso
PLC
Siemens S7 para Programadores

Este curso ha sido diseñado para aquellas personas que quieran profundizar sus conocimientos en el uso de los sistemas…


Leer más

Curso
PLC Siemens S7-1200-1500
TIA Portal | Maintenance

After the training the participant is capable of managing a new TIA Portal application. He can also implement…

Leer más

Curso
PLC Siemens S7-1200-1500
TIA Portal | Programming

After the training, the participant will be able to program a new TIA Portal application or implement a major change…

Leer más

Curso
Siemens
S5 – Programadores

Este curso ha sido diseñado para aquellas personas que se inicien en el uso de los sistemas…

Leer más

Curso
PLC Mitsubishi FX/A and
System Q Maintenance

Este curso ha sido diseñado para aquellas personas que se inicien en el uso de los sistemas de control de…

Leer más

Curso
PLC Mitsubishi FX/A y
System Q para Programadores

Este curso ha sido diseñado para el personal de mantenimiento que necesite identificar y solucionar problemas con el PLC sistem…

Leer más

Curso
PLC – Allen – Bradley
ControlLogix Maintenance

Este curso ha sido diseñado para ingenieros que necesiten diseñar y configurar un sistema ControlLogix…

Leer más

Curso
PLC – Allen – Bradley
ControlLogix Avanzado

Este curso está dirigido a usuarios de Allen-Bradley ControlLogix que necesiten tener una comprensión…

Leer más

Curso
PLC – Allen – Bradley
PLC-5

Este curso está diseñado para aquellos nuevos usuarios de Allen-Bradley PLC-5 que deseen adquirir un conocimiento…

Leer más

Curso
PLC – Allen – Bradley PLC-5,
SLC500 and MicroLogix

This course is designed for maintenance personnel who have to maintaine and solve problems on the Allen-Bradley…

Leer más

Curso
PLC – Allen – Bradley
SLC-500

Este curso ha sido diseñado para nuevos usuarios de Allen-Bradley SLC-500 que quieran adquirir un conocimiento…

Leer más

Esquema de impartición / Plazas abiertas