Training: PLC – Allen-Bradley PLC-5, SLC500 and MicroLogix

Duur:

Kosten: EUR 1580

Planning

This course is designed for maintenance personnel who have to maintaine and solve problems on the Allen-Bradley MicroLogix, SLC-500 and PLC-5 platforms. This course uses the Rockwell Software products RSLogix 5, RSLogix 500* and RSLinx.

Target Group
This course is designed for maintenance personnel who have to maintaine and solve problems on the Allen-Bradley MicroLogix, SLC-500 and PLC-5 platforms. This course uses the Rockwell Software products RSLogix 5, RSLogix 500* and RSLinx.

(Pre) Knowledge
To join this course a basic knowledge of Windows and Allen-Bradley PLC possibilities is required.

Global Contents
Maintenance personnel are often confronted with equipment from several manufacturers. This course recognises that maintenance personnel cannot build up a profound technical knowledge of all the equipment to be maintained. One needs to have sufficient knowledge of the equipment, coupled with knowledge of the installation to be able to diagnose the problem and then solve the problem.

With regard to PLC’s and programming software, the maintenance engineer needs to be able to access specific parts of the program and to examine the I/O status. Programming and documenting the program is of less importance. The maintenance engineers should be capable of making small changes to the program.

Problems are most likely to occur with the installation itself and this is reflected in the PLC by for instance a defective sensor, a badly working cylinder etc. These faults can be investigated via the programming software and the signal status can be presented dynamically. This is necessary, because designers are not always able to design their programs to register every possible fault and the potential cause.

The maintenance engineer should therefore be capable of executing the following actions:

  • To be able to identify if the PLC is still active and that there are no communication errors with the I/O or other coupled PLC’s.
  • To determine that the signal of the ‘suspected’ unit will show at the correct PLC input / output. To install and to start the programming software.
  • To make the internal I/O status of the signal visible:
    to call the ‘suspected’ section in the program;
    to make timer and counter files visible.
  • The maintenance engineer must be able to read the documentation, understand the structure of the PLC and be aware of the most commonly used PLC instructions.
  • To make links or to develop connections that changes the program conditions. Programming a counter and time measurement is desirable.
  • To make a backup of the changes made to the program. The maintenance engineer should also be capable of making an (original) backup of the program and be able to load it into the PLC.

Methods
ATS courses are given by highly qualified trainers, with practical knowledge, in professional ATS training centers or On-Site. Prior to the course an intake conversation can take place to define the participant(s) and the company’s requirements. Presentations (theory and examples) as well as practical exercises bring the courses to life. ATS courses are interactive, the trainer will always make sure the training contents link back to your situation.

Specifieke inhoud

  • Lesson 1

    • Hardware of the Allen Bradley SLC500 / PLC5
    • I/O electric connections for various modules
    • Rack grouping
    • Developing, monitoring & documentation software
  • Lesson 2

    • General features of the Allen Bradley PLC family
    • IEC 1131 ‘compliant’ software structure
    • Ladder software and editing
  • Lesson 3

    • The RSlogix 5 / 500 programming package
    • Connecting the PLC and starting up the software
    • Selecting the PLC correct program
    • Help functions
    • Programming instructions, including the modifications of existing AND and OR gates, flip-flops, timer functions and counter functions
  • Lesson 4

    • To copy, to change and to store the PLC-programs
    • Fault finding
    • Off-line & On-line mode
    • Monitoring and modifying data variables
    • Forcing variables
    • Cross references
    • Software documentation
    • Using trends and data monitors
  • Lesson 5

    • Up- and downloading programs
    • Writing, testing, and documenting a PLC-program
    • Identifying data and data types and interpreting the different formats

Meer informatie

Onze open trainingen gaan door zodra er minimaal 4 en maximaal 8 deelnemers aangemeld zijn. Wilt u zich aanmelden voor onze open trainingen, klik dan op ‘aanmelden’ naast de gewenste datum en locatie om het aanmeldingsformulier in te vullen. Heeft u vragen over de planning van een training, dan kunt u altijd contact met ons opnemen.

Wilt u deze training boeken als bedrijfstraining of heeft u andere vragen? Doe dan een informatie aanvraag

AGENDA

Datum: Op aanvraag
Locatie: Nederland
Kosten:  EUR 1580.00

Andere mogelijkheden

Training
Introductie
PLC-techniek

Programmeerbare Logische Controllers (PLC) vormen het hart van besturingsinstallaties van vele technische systemen…

Lees meer

Training
Siemens S7
Classic | Beheren

Siemens S7-300 en S7-400 PLC’s vormen het hart van menig productiesysteem binnen een productiebedrijf…

Lees meer

Training
Siemens S7 Classic
| Programmeren

Deze cursus is bestemd voor beginnende Siemens S7 gebruikers die diepgaande kennis van de SIMATIC…

Lees meer

Training
Siemens S7 TIA Portal
| Beheren

Na de training is de deelnemer in staat om een nieuwe TIA Portal applicatie te beheren. Ook kan hij wijzigingen…

Lees meer

Training
Siemens S7 TIA Portal
| Programmeren

Na de training is de deelnemer in staat om een nieuwe TIA Portal applicatie te programmeren of een grote wijziging door…

Lees meer

Training
PLC
Siemens S5

Deze cursus is bestemd voor beginnende Siemens S5 gebruikers die diepgaande kennis willen opbouwen…

Lees meer

Training
Mitsubishi FX/A en System Q
| Beheren

Deze cursus is bestemd voor personeel van storing- en onderhoudsdiensten die storingen moeten verhelpen aan Mitsubishi FX/A…

Lees meer

Training
Mitsubishi FX/A en System Q
| Programmeren

Deze cursus is bestemd voor beginnende Mitsubishi gebruikers die kennis en ervaring willen opdoen van de Mitsubishi

Lees meer

Training
PLC – Allen – Bradley
ControlLogix 

Deze cursus is bedoeld voor engineers die moeten kunnen omgaan met een ControlLogix-systeem…

Lees meer

Training
Allen-Bradley ControlLogix
| Gevorderd programmeren

Deze training is bestemd voor Allen-Bradley ControlLogix gebruikers die een meer diepgaande kennis…

Lees meer

Training
Allen-Bradley
PLC-5

Deze cursus is bestemd voor beginnende Allen-Bradley PLC-5 gebruikers die diepgaande kennis…

Lees meer

Training
PLC – Allen-Bradley PLC-5, SLC500
and MicroLogix 

This course is designed for maintenance personnel who have to maintaine and solve problems on the Allen-Bradley…

Lees meer

Training
Allen-Bradley
SLC-500

Deze cursus is bestemd voor beginnende Allen-Bradley SLC-500 gebruikers die diepgaande kennis willen…

Lees meer

Open trainingsagenda / Open plaatsen